• Alphanumeric 16x2 LCD Display
• Six digit 7-segment display interface.
• 8 LEDs interfaced using serial shift register.
• 4x4 Keypad
• 8 bit successive Approximation ADC and temperature sensor interface
• 8 bit DAC interface
• I2C interface RTC, NVROM
• SPI Interface to 12bit ADC
• Four level Elevator simulator interface.
• On-board stepper motor and DC motor control interface.
• Solid State Relay and Buzzer interface.
• RF Receiver and RF Transmitter
• IR receiver with remote controller.
• 8 pin DIP switch interface
• Variable frequency and Pulse Width Modulation generator using dual timer.
• Compare, Capture and PWM demo using on-chip PCA.
• RS485 AND RS422 interface
• A number of software examples in C-Language’ to illustrate the functioning of the interfaces. The software examples are compiled using an evaluation version of KEIL `C’ Compiler for 8051 and a monitor program allows debugging of the user programs in Controller Flash Memory.

• Three programmable Timer/Counters
• Two External Interrupts
• The Atmel AT89C51ED2- 8-bit micro controller with operating frequency of 11.0592MHz with an external crystal and supply voltage of +5V.
• Four 10 pin FRC connectors connected to Port-0, to Port-3 of the controller
• One 26 pin FRC to connect to ALS standard NIFC interfaces
• A 9-pin D-type female connector used for RS232 serial I/O interface for UART experiments and also for flash programming. Serial interface through USB is also provided onboard
• A Push button switch for Reset and a Slide switch to select either program mode or run mode.
• A Push button switch for External Interrupt /INT0 or /INT1.
• Alphanumeric 16x2 LCD display.
• Two numbers of LED‘provided for general purpose.
• 16 switches organized as 4 rows X 4 columns.
• 8-bit DAC interface
• RTC interface
• One ADC (ADC0809) with a Potentiometer to vary analog input & Temperature Sensor IC LM335
• Four level Elevator simulator interface.
• Traffic Light simulator interface
• On-board stepper motor and DC motor control interface. Stepper motor and DC motor is supplied with evaluation board.
• Four-digit multiplexed 7-segment display interface.
• Test Points for monitoring
• A number of software examples in ‘C-language’ to illustrate the functioning of the interfaces. The software examples are compiled using an evaluation version of KEIL ‘C’ compiler for 8051 and a monitor program allows debugging of the user programs in Controller Flash memory

• RS232 compatible serial interface for communication and ISP.
• Alphanumeric 16x2 LCD Display
• Six digit 7-segment display interface.
• 8 LEDs interfaced using serial shift register.
• 4x4 Keypad
• 8 bit successive Approximation ADC and temperature sensor interface
• 8 bit DAC interface
• I2C interface RTC, NVROM
• SPI Interface to 12bit ADC
• Three level Elevator simulator interface.
• On-board stepper motor and DC motor control interface.
• Solid State Relay and Buzzer interface.
• 8 pin DIP switch interface
• Variable frequency and Pulse Width Modulation generator using dual timer.
• Compare, Capture and PWM demo using on-chip PCA.
• RS485 AND RS422 interface
• A number of software examples in `C-Language’ to illustrate the functioning of the interfaces. The software examples are compiled using an evaluation version of KEIL3 `C’ Compiler for 8051 and a monitor program allows debugging of the user programs in Controller Flash Memory.

• One 26 pin FRC to connect to some ALS standard NIFC interfaces
• The Atmel AT89C51ED2- 8-bit micro controller with operating frequency of 11.0592MHz with an external crystal and supply voltage of +5V.
• Four 10 pin FRC connectors connected to Port 0 to Port 3 of controller
• A 9-pin D-type female connector used for RS232 serial i/o interface for UART experiments and also for flash programming. Serial interface through USB is also provided onboard
• A 9-pin D-type male Connector meant for power connection (+5V and GND)
• A Push button switch for Reset and a Slide switch to select either program mode or run mode.
• A Push button switch for External Interrupt /INT0 or /INT1.
• Alphanumeric 16x2 LCD display
• Two numbers of LED's provided for general purpose .
• 16 switches organized as 4 rows X 4 columns.
• 8-bit DAC interface
• RTC interface
• One ADC (ADC0809) with a Potentiometer to vary analog input & Temperature Sensor IC LM335
• Four level Elevator simulator interface.
• Traffic Light simulator interface
• On-board stepper motor and DC motor control interface. Stepper motor and DC motor is supplied with evaluation board.
• Four-digit multiplexed 7-segment display interface.
• Elegant enclosure with Test Points for monitoring A number of software examples in ‘C-language’ to illustrate the functioning of the interfaces. The software examples are compiled using an evaluation version of KEIL ‘C’ compiler for 8051 and a monitor program allows debugging of the user programs in Controller Flash memory

• One RS232 interface circuits with 9 pin DSUB connector: this is used by the Boot loader program, to program LPC2148 Flash memory without external Programmer
• Piggy Back module containing LPC2148 controller
• Standard JTAG connector with ARM 2×10 pin layout for programming/debugging with ARM-JTAG
• Standard 26-pin FRC connectors to connect to on-board interface or some of ALS standard External Interfaces
• Reset push-button for resetting the controller
• SPI Interface: 2 channel ADC IC with POT and Temperature sensor
• I2C Interface: NVROM IC
• On chip ADC interface circuit
• Two External interrupt circuits with LED indication
• LCD 16×2 alphanumeric display
• On-board eight push-button switches
• 4x4 Key-Matrix connected to the port lines of the controller
• Eight general purpose LED’s
• Four-digit multiplexed 7-segment display interface
• 8-bit DAC interface
• Stepper motor interface with direction and speed control
• DC motor interface with direction and speed control
• Interface circuit for on board Buzzer and Relay
• A number of software examples in ‘C-language’ to illustrate the functioning of the interfaces. The software examples are compiled using an evaluation version of KEIL4 ‘C’ compiler for ARM
• Compact elegant plastic enclosure
• Serial RS232 cable is included
• Operates off 5V DC

• Power- supply for external power supply 9 PIN D type and also provision for adaptor
• USB _ B type connector for downloading the program
• Piggy Back module containing LPC2148 controller
• Standard JTAG connector with ARM 2×10 pin layout for programming/debugging with ARM-JTAG
• Standard 26-pin FRC connectors to connect to on-board interface or some of ALS standard External Interfaces
• Reset push-button for resetting the controller
• I2C& SPI-Port terminated in Berg for external interfacing
• On chip ADC interface circuit
• On chip DAC interface circuit
• UART0- USB for serial communication & UART1 for user application
• PWM
• External interrupt
• Onboard 1” OLED
• 16X2 LCD
• 4x4 key matrix connected to the port lines of the controller
• Four general purpose LED’s
• Stepper motor interface with direction and speed control
• DC motor interface with direction and speed control
• On board relay
• On board buzzer
• Two digit Seven segment display
• On board Sensors like
  • TEMPERATURE
  • PIR SENSOR
  • GAS SENSOR
  • ULTRASONIC Sensor
• Compact elegant plastic enclosure
• Operates off 5V DC

• Reset push-button for resetting the controller
• Three of the four controller UART's are made available to user for external interfaces
• - UART0: General purpose RS232 terminated in a 9 pin female DSUB connector which is also used to program LPC1768 Flash memory without external Programmer
• - UART1: General purpose RS485 terminated in a 3 pin male reliamate
• - UART2: General purpose RS232 terminated in a 3 pin male reliamate
• Interface to Controller internal ADC and DAC
• 16×2 alphanumeric LCD and 128×64 Graphic LCD display are provided – one of them can be used at a time
• 4×4 Key-Matrix
• SPI interface: Flash NVROM memory circuit
• Simple I2S demonstration circuit
• I2C interface: RTC IC
• Eight general purpose LED’s
• Four-digit multiplexed 7-segment display interface
• 8-bit DAC interface
• Interface circuit for external Interrupt
• Interface circuit for Capture & match
• Interface circuit for PWM with a monitor LED
• On-board stepper motor, DC motor control, Relay interface
• Interface circuit for on board Buzzer
• Two CAN interfaces with reliamate connector
• Some of the on board interfaces connect to the Controller using short standard 10 pin FRC cables while the others are connected directly
• Standard JTAG connector with ARM 2×10 pin layout for programming/debugging with ARM-JTAG
• Standard Emulation Trace connector with 2×10 pin layout for CPU Execution tracing
• One standard 26-pin FRC connector to connect to some of ALS standard External Interfaces
• A number of software examples in ‘C-language’ to illustrate the functioning of the interfaces. The software examples are compiled using an evaluation version of KEIL4 ‘C’ compiler for ARM

• • 70 General Purpose I/O (GPIO) pins with configurable pull-up/down resistors, open drain mode, and repeater mode.
  • 12-bit Analog-to-Digital Converter (ADC)
  • Four external interrupt inputs configurable as edge/level sensitive
  • Four general purpose timers/counters, with a total of eight capture inputs and ten compare outputs.
  • Four UART's with fractional baud rate generation, internal FIFO, IrDA.
  • SPI controller with synchronous, serial, full duplex communication.
  • Three enhanced I2C-bus interfaces
  • Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down.
  • Real-Time Clock (RTC) with a separate power domain.
  • Standard JTAG test/debug interface as well as Serial Wire Debug.
• 12MHz Crystal allows easy communication setup
• One on board voltage regulator for generating 3.3V. Input to this will be from External +5V DC Power supply through a 9-pin DSUB connector
• Piggy Back module containing LPC1768 controller
• Standard JTAG connector with ARM 2×10 pin layout for programming/debugging with ARM-JTAG
• Reset push-button for resetting the controller
• One RS232 interface circuit with 9 pin DSUB connector: this is used by the Boot loader program, to program LPC1768 Flash memory without external Programmer. Application program can also use this UART for serial communication
• DC motor interface with direction and speed control
• Stepper motor interface with direction and speed control
• 16×2 alphanumeric LCD Display
• On chip ADC interface circuit with POT
• 8-bit DAC interface
• 4x4 Key-Matrix connected to the port lines of the controller
• One External interrupt circuit with LED indication
• Two-digit multiplexed 7-segment display interface
• Interface circuit for on board Buzzer, Relay and Led indication controlled through push button.
• SPI Interface: 2 channel ADC IC with POT and Temperature sensor
• I2C Interface: NVROM IC
• Internal PWM terminated in test point and LED
• Standard 26-pin FRC connectors to connect to on-board interface or some of ALS standard External Interfaces.
• A number of software examples in ‘C-language’ to illustrate the functioning of the interfaces. The software examples are compiled using an evaluation version of KEIL4 ‘C’ compiler for ARM.
• Optional USB to Serial interface (RS232) cable.

• Four-digit 7-segment displays connected through 10 PIN FRC connector to FPGA/CPLD port pins.
• 4x4 key matrix.
• 10 MHz, 5 MHz, 1MHz, 500 KHz, 100 KHz - five different clock frequencies.
• On-board Relay connected using 10 pin FRC to FPGA/CPLD port pins.
• On-board ADC connected to FPGA/CPLD port pins using 16 pin FRC.
• On-board DAC is provided to generate different waveforms and it is Connected to FPGA/CPLD port pins using 16 pin FRC.
• On-board four level Elevator connected to FPGA/CPLD port pins using 16 pin FRC.
• Two-pin reliamate is provided on the board to connect external DC motor and it is connected to FPGA/CPLD port pins using 10 pin FRC.
• 5-way PowerMate is provided to connect external stepper motor and it is connected to FPGA/CPLD port pins using 10 pin FRC
• 26-PIN FRC header with Cable for connecting to ALS standard interfaces
• 8 inputs using 0ne DIP switches. Each input of these switches has an LED indication.
• One push button
• Four sets of 20x2 female berg connector to plug the DAUGHTER BOARD.
• Programs can be downloaded from the PC to the FPGA/CPLD on the daughter board using Programming tool

DAUGHTER BOARD - 6

• XLINIX XC6SLX4TQ144: SPARTAN6 FPGA
• Platform flash in-system programmable configuration PROM: XCF04SVO20
• 16 PIN FRC connector to select between base board toggle switch and the 26 pin FRC external interface.
• JTAG connector (10 PIN FRC connector) for boundary scan programming.
• Push-button switch to re-initialise the FPGA and DONE LED for program status indication
• Power from the bottom board.
• Four sets of 20 X 2 berg connectors for plugging on to the base board.

BASE BOARD

• The 12 inputs are connected to DIP switches and 12 outputs are connected to LED’s and also terminated in pads. The status of inputs are also indicated through LED’s and the inputs are also terminated in pads
  A number of experiments like combination controller (AND, OR, XOR and NOT operations), sequential controller, programmable counter, multiplexer etc. can be conducted using this interface
  The interface operates off 5V DC and is housed in our standard plastic box
• NIFC-06A - DUAL DAC INTERFACE
  This interface allows the user to study 8 bit DAC (0800) for wave form generation. It has two DACs
• NIFC-07A - 8 BIT SUCCESSIVE APPROXIMATION ADC INTERFACE
  This is based on ADC0809, which is an 8 bit 8 channel ADC with input multiplexer. The conversion time is 100 microseconds. Input voltage range is 0 to 5V
• NIFC-09 - KEYBOARD/DISPLAY INTERFACE
  This provides the user with 20 keys and a 4 digit display mounted on a single board
• NIFC-11 - TRAFFIC LIGHT SIMULATOR
  This provides an example as how the traffic signals are controlled using a processor. The signals are indicated by means of Red, Green and Amber LED’s
• NIFC-17 - ELEVATOR INTERFACE
  This interface is designed to simulate an elevator. The interface is an example of a four storey building with Green LED indicating that the elevator is in a particular floor and RED indicating request
• NIFC-41 - TEMPERATURE MEASURMENT INTERFACE
  This interface consists of a Probe mounted AD590 Temperature Sensor, conditioning Electronics and an 8 bit ADC, AD0809
• NIFC-45 - LCD AND KEYBOARD INTERFACE
  The interface consists of single line 16 character LCD display and a 4X4 hex keypad.
• ALS-NIFC-55
  DC Motor Interface
• STUDY CARDS
  NIFC -15 - 8255 Study Cards, NIFC -21 - 8253 / 8251 Study Cards, NIFC -24 - 8279 Study Cards,

FINGERPRINT READER INTERFACE ALS-NIFC-70

SPECIFICATIONS

ALS -NIFC-70 interface allows study of a fingerprint reader . Access control systems based on finger prints are being used widely in our daily lives. These systems use the basic principle that no two fingerprints match and this provides a convenient means to identify people.Finger print reader which has a serial two wire interface with necessary optics to scan a finger, record the image of the finger and subsequently allow comparison of scanned finger with data stored in its database.

The two line alphanumeric LCD display in the controller board allows display of user messages .The board also contains LED’s to indicate proper scan and also a match. A relay is provided which turns on when a match is detected and its contacts can be used to energies a door lock. A 16 key hex keypad is included to allow ID selection.

• It has one R305 Fingerprint module to scan and compare finger match.
• Relay - provides switched contacts for control.
• Buzzer and status LED are provided for status indication
• Test points are provided for observation purpose
• Power – 5V DC
• Two controller spare i/o line is terminated and can be used as required
• Three 26 core IDC FRC male connectors to connect ALS-SDA-ARM7-2148,ALS-SDA-CRTXM3 or MSP430-F5529 EVAL BOARDS
• Board size 100 x 160 mm
• Elegant plastic enclosure for the board

RFID INTERFACE ALS-NIFC-71

SPECIFICATIONS

ALS -NIFC-71 interface allows study of RFID device. Access control systems based on RFID technology are being used widely in our daily lives. RFID is only one of numerous technologies grouped under the term Automatic Identification (Auto ID)Auto ID technologies are a new way of controlling information and material flow, especially suitable for large production networks.RFID reader which has a serial two wire interface with necessary antenna.

The RFID tags are used to store the data and retrieve the data of particular person to enter into home or particular room in office. The two lines alphanumeric LCD display in the controller board allows display of user messages.Successful password entry is indicated by the partial rotation of a DC motor to indicate access.

• It has one13.56MHz MIFARE read/write module.
• MIFARE S50 tags are provided to store the user’s information and also for reading the stored data
• Access control motor operates at either 5V or 12V DC
• Buzzer and status LED are provided for status indication
• Test points are provided for observation purpose
• Power – 5V DC
• Two controller spare i/o line is terminated and can be used as required
• Three 26 core IDC FRC male connectors to connect ALS-SDA-ARM7-2148,ALS-SDA-CRTXM3 or MSP430-F5529 EVAL BOARDS
• Board size 100 x 160 mm
• Elegant plastic enclosure for the board

GRAPHIC LCD DISPLAY INTERFACE ALS-NIFC-76

SPECIFICATIONS

ALS-NIFC-76 is GRAPHIC LCD DISPLAY Interface with Ultrasonic Distance Sensor (GP2Y0A21YK0F), Hall Effect Sensor (A1104), Pressure and Temperature Sensor (BMP180). A Graphic display allows display of alphanumeric characters and symbols. Measured parameters like RPM, Distance in cms, Pressure in hpa and temperature in Deg C can be displayed on the GLCD.

• Graphic LCD 128x64(JHD12864E)
  • DISPLAY CONSTRUCTION : 128*64 DOTS
  • DISPLAY MODE : :STN / Yellow
  • DISPLAY TYPE : Green Positive Tranflective
  • VIEWING DIRECTION : :6 o’clock
  • OPERATING TEMPERATURE : Indoor
  • DRIVING VOLTAGE : Single power
  • DRIVING METHOD : 1/64 duty, 1/9 bias
  • TYPE : COB (Chip On Board)
  • NUMBER OF DATA LINE : 8-bit parallel
  • CONNECTOR : Pin
• Ultrasonic Distance Sensor (GP2Y0A21YK0F)
  • 10 to 80 cm Range
  • 39 ms Typical response time
• Hall Effect Sensor (A1104)
  • AEC-Q100 automotive qualified
  • Continuous-time operation
  • Stable Operation over Full Operating Temperature Range.
• Pressure and Temperature Sensor (BMP180)
  • Pressure range: 300 ... 1100hPa (+9000m ... -500m relating to sea level)
  • Supply voltage: 1.8 ... 3.6V
  • Temperature measurement included
  • I2C interface.
• Ultrasonic distance sensor – SHARP sensor (GP2Y0A21YK0F) -measures the object distance from 10 to 80 cm.
• Hall Effect rpm sensor with DC motor carrying shaft mounted magnet.
• Speed of DC motor (+5V/+12V) can be varied using external Variable DC power supply.
• Atmospheric pressure sensor BMP180 measures 300 to 1100 Hpa absolute pressure range and temperature in Deg C can be displayed on the GLCD with I2C interface.
• All the above parameters are displayed on the graphic LCD
• One RED LED for power indication.
• Regulator is provided to generate 3.3V.
• Three 26 core IDC FRC male connectors to connect to ALS-SDA-ARM2148,ALS-SDA-CRTXM3 or MSP430-F5529 EVAL BOARDS.
• Elegant plastic enclosure for the board.

HARDWARE FEATURES

Processor

• TMS320C6748 DSP at 456-MHz C674x Fixed/Floating Point DSP
• On-Chip RTC

On board Memory

• 128 MByte DDR2 SDRAM running at 150MHz
• 128 MByte 16-bit wide NAND FLASH
• 8MB SPI Flash

On board Codec

• TLV320AIC3106 Stereo Codec

Interfaces

• One mini-USB Serial Port (on-board serial to USB)
• One Fast Ethernet Port (10/100 Mbps) with status LEDs
• One USB Host port (USB 1.1)
• One mini-USB OTG port (USB 2.0)
• One LCD Port
• Two AUDIO Ports (1 MIC IN/1 LINE IN & 1 LINE OUT )
• 14-pin JTAG header

KIT CONTENTS

C6748/OMAP L138 DSP Hardware Board
• Power Adapter
• XDS 100 JTAG Emulator
• USB cable
• User Manual
• Code composer studio (E-Download)

SOFTWARE FEATURES

• A complete Integrated Development Environment (IDE), an efficient optimizing C/C++ compiler assembler, linker, debugger, an a advanced editor with Code Maestro™ technology for faster code creation, data visualization, a profiler and a flexible project manager
• DSP/BIOS™ real-time kernel
• Target error recovery software

All the inputs and outputs are brought out to the panels for the ease of studying various Static application panels and also Sample Ladder programs are supplied for better understanding of PLC. The Panel is built with necessary Power supply required for the PLC and the Simulation Panels. The system can be used for any control applications, which come across in Industrial Environment by writing Logic program as per requirement.

DISTRIBUTOR PANEL

• For Easy connection of input/output of PLC to the field / Static application through use of patch cords

FOR DIGITAL INPUT & DIGITAL OUTPUT

• Consist of 8 Digital inputs and
• 6 Digital Output
• 4mm socket for Digital Input : 8 nos
• 4mm socket for Digital output : 6 nos

SIMULATION + EXTENSION PANEL

For simulation of Digital I/Os and extension for inputs and outputs for connecting the same I/P or O/P at different points.
• Digital I/P consists of Toggle switches : 4 nos.
• Pushbuttons : 4 nos. ; 4mm Socket: 8 nos.
• Digital outputs consists of 24 V DC LED : 6 nos.

FEATURES

• Front - end connection through 4mm sockets and patch cards or fixed I/O connection with Toggles switches and L.E.Ds
• Various Static application dependent programs to be interfaced with PLC
• Learning and Troubleshooting Skills through front panel
• Study of Ladder Diagram
• Dynamic Ladder display on Personal Computer
• Light weight study panel
• Sufficient Courseware: Literature for Various Static application dependent programs Instructor’s Guide, Technical Reference.

SPECIFICATION OF PLC

• Make - ABB
• DI - 8 Built in
• DO - 6 Built in
• PC Interface - RS 232 Cable

WORKING MODULES

• Motor Control
• Interfacing of Motors
• Water Level controller
• Bottling System
• Elevator

SAP MODULES FOR INTERFACING

• Conveyer simulation module
• Water level control
• Lift control
• Counting of pulses & switching of lights
• Traffic light control
• Logic gate simulation
• Dol starter and star delta
• Panel for on dely off delay timer
• Panel for alaram systems
• Bolian algebra demorgans theorem panel
• Process control application for fan
• Panel for on delay off delay timer
• Panel for mixing process
• Panel for counter & comparision
• Traffic light control using plc sap module
• Car parking simulation
• Garage door simulation
• Module for washing machine